HIGHLIGHTS
Undisturbed flow
Breach Recovery
Delivers a harmoniously balanced ride
WHAT RIDERS SAY
"The Stabilizer breaching the surface is like a warning signal, but it's not catastrophic. Simply push down the nose of the board to adjust your ride height, then foil on." - Uli Sommerlatt, Foil Designer
FLIGHTATTENDANT 2Designed with ease of use in mind.
FlightAttendant foils are easy to ride all-rounders. The easy takeoff, stiffness, ventilation resistance, and mid-aspect platform make this a foil that can be used by any rider in almost all conditions.
New design features are made in an effort to increase turning, glide, and most of all predictability. Increased predictability helps you advance your riding from learning on flat water, through to massive jumps and fully ventilated turns.
The profile, outline, twist and taper have been developed in order to allow for great stability, efficiency, easy take off at low speed, and superior maneuverability. All while allowing for impressive performance over a very wide range of speeds.
The curved wingtips keep ventilation from moving up when getting close to the surface, making the FlightAttendant extremely forgiving.
The front wing and stabilizer perfectly complement each other, allowing for a short fuselage that results in a foil that is amazingly stable, and very easy to maneuver.
The outline and perfectly tuned wing and stabilizer will amaze you when effortlessly pumping from one wave to the next.
About our design goals for the new FlightAttendant
The new design features are made in an effort to increase turning, glide, and most of all predictability. We found increased predictability helped advance peoples riding from learning on flat water through massive jumps and fully ventilated turns.Aspect: The Collection 3 foils have a higher aspect ratio to increase the glide/turn ratio. They are also flatter with a less aggressive overall curvature to increase speed and ventilation resistance.Profile: The profile was chosen based on a few factors- ease of takeoff, speed range, and ventilation resistance. The airfoil on the flight attendant has a very low stall speed and high stall angle. This helps get you on foil easily with a wide range of boards, sails, skill level, and conditions. It also helps when landing jumps and pivoting in the pocket.The wingtips have been slightly flattened and straightened this generation. The airfoil gain in ventilation resistance lets us run less curvature in the tip.Fuselage: The new fuselage has been revised to reduce weight and drag while increasing modularity. The mast now uses a conical box-style connection, for absolute rigidity between mast and fuselage, the tail section has a reduced section, and the front wing connection is hollowed out.
IC6 950 V.3
The IC6 950 is very accessible and grants a surprising potential for progression. It is really the ideal first foil purchase, and its versatility will lead to fast and satisfying improvements throughout your foiling journey.
Aspect Ratio: 4.4
Very user-friendly
Versatile, intuitive, and predictable
Large range of use
ALU MAST
45 > 95 CM
The F-ONE aluminum mast can be used for all disciplines: kite, surf foil, wing foil, SUP foil and windfoil. The profile is extruded with precision from 6063 aluminum block.
The shape of its section benefits from our years of experience in kite foiling to provide the best gliding feel while keeping the strength up and the weight down. It comes with two stainless steel helicoil inserts at the bottom and at the top to fasten the connecting parts and is therefore fully modular.
The aluminum mast can be used on every foil of the range, and it is very easy to jump from one length to another (45 / 55 / 65 / 75 / 85 / 95 cm).
A number of parts are available for board connection (Plate, KF, Deep KF, Tuttle).
The Sonar High Aspect Front Wing Series is engineered for the highest speed and efficiency possible across a range of disciplines – from kite foiling to prone foil surfing. With this style of wing, you need minimal pump and power to generate glide. The shorter chord length defines the profile thickness, and with a thin profile comes reduced drag. The span gives you stability and a slightly longer radius turn than a lower aspect ratio wing of the same size. The wingtips are refined to ensure there is no ventilation when you tip breach, giving you the ability to crank tighter radius turns at higher speeds, without losing speed. The smaller HA650 have less planing surface and higher stall speed. They are designed to generate maximum efficiency and lift for high-speed wing foiling, racing, and kite foiling.
The Sonar High Aspect Front Wing Series is engineered for the highest speed and efficiency possible across a range of disciplines – from kite foiling to prone foil surfing. With this style of wing, you need minimal pump and power to generate glide. The shorter chord length defines the profile thickness, and with a thin profile comes reduced drag. The span gives you stability and a slightly longer radius turn than a lower aspect ratio wing of the same size. The wingtips are refined to ensure there is no ventilation when you tip breach, giving you the ability to crank tighter radius turns at higher speeds, without losing speed. The larger HA1450 is ideal for dock starts, pumping to connect wave after wave, coastal runners or stealing wakes. Downwinding: Ocean swells move faster in the open ocean – slower in shallow water or closer to the coast. The faster you move through the water, the more choice you have to choose a more efficient line. The smaller the wing, the less planing surface = less lift and higher stall speed. The HA Series Wings are designed for lighter / more experienced riders to foil in faster-moving ocean swells.
FUSION CARBON HOLLOW MAST
HIGH PERFORMANCE - LIGHT WEIGHT
SIZES: 74 / 84 / 94 CM
The all-new Hollow Mast system is yet another example of the state of the art foil program from Cab Design Works. It nods to the critical & complete design approach of the team to view every foil component individually with a view to improve stiffness across the entire platform. It implements a bladder molded construction with strategic layering of carbon as far to the outside as possible. This culminates in our stiffest ever mast to front wing connection. This reduction in flex eliminates any lag in the turn and transfers energy while pumping seamlessly through to the front wing.
Features:
Optimized airfoil for low drag to stiffness ratio
TE scallop for improved turning and efficiency
Integrated high modulus mounting plate
Bladder molded, hollow mast construction for superior skin compression, providing ultimate rigidity
Premium high modulus prepreg carbon fiber construction
Barrel Nut compatible(x-series MkII and H-series MKII)
Tapered Fit
Mast Guide:
FUSION ALLOY TOP PLATE MKII
HIGH PERFORMANCE - DURABILITY
SIZES: ONE SIZE
The Fusion Alloy Top Plate is constructed from extruded aircraft grade aluminium that result in an incredibly rigid mast to board socket connection. It can be used with any Cab Fusion alloy mast.
Features:
Precision CNC machined aircraft grade, anodized 6061-T6 aluminium
Incredible torsional stiffness
FUSION H-SERIES KITS
HIGH ASPECT
SIZES: H550 / H700 / H850 / H1050 / H1300
Just when you thought a product couldn’t get better, the new H-Series MkII pushes into the future of foil design and sets a new benchmark for efficiency and performance. The design team have implemented new technology learnt from the collaboration with Sintef. Water testing in the biggest tank in Europe has refined the H-series tip shape to allow the tips to breach and re-enter without cavitation. This allows more progressive riding and radical turns, be it with a kite, wing or prone. The new leaner profile now boasts an increased speed range which helps entry into freestyle tricks or on the race field. It seamlessly pairs with any of Cabrinha’s V-series stabs and is part of the modular Cab Fusion system.
The Fusion H-Series Kits come with everything you need, you just need to add your mast of choice. (Masts sold separately)
INCLUDED IN KIT
Wing & Stabilizer
Fusion Fuselage Alloy Medium
Track Nut Train X2
Screw Set Foam Core Boards
Wing Features:
Ultra Efficient Design
Ultra Lean Profile
Refined Tip Shape.
Tapered Fit
Increased Torsional Stiffness
High Aspect Ratio
Barrel Nut Secure Connection
Pre Preg Carbon Construction
Modular Design to work with Cab Fusion Products
Tech Specs
H550- 550cm², WS 690, AR 9.52, Chord 110mm
H700- 700cm², WS 815, AR 9.49, Chord 120mm
H850- 850cm², WS 900, AR 9.53 Chord 130mm
H1050- 1050cm², WS 1000, AR 9.52, Chord 140mm
H1300 - 1300cm ², WS 1090, AR 9.14, Chord 150mm
H800- 800cm ², WS 900mm, AR 9.9, Chord 125mm
H1000- 1000cm ², WS 900mm, AR 8.1, Chord 155mm
Wing Guide:
Freefoil | SurfBalanced by design.Even, predictable flight. Easy, steady takeoffs. And super smooth turns. The larger size imparts a more balanced flight behavior at all speeds. The dihedral curvature lets you tilt the foil into turns like a skateboard for a smoother cruising behavior. Gybes, tacks, 360s, and transitions are much easier since you can feel your back wing and use it to pivot the foil. A high-quality lightweight carbon and PU foam construction is more complex to build than a pure carbon wing but the weight savings is worth it.Delivery: Stabilizer only.Sizes:Stabilizer: 300cm2Features:
PU CARBON SANDWICH: Very light and responsive.
DIHEDRAL STABILIZER: Smooth, balanced gybes.
Designed for our entire foil line, the AXIS masts are stiff, strong, and ready for any use and conditions. We designed our masts for 2021 to give our foilers a very direct feeling to their foil which is critical for foiling. We even sourced our own high quality aluminium and bought tons of it, to ensure we only have the highest quality raw materials for our foils. Our masts are 224% stiffer than the 15mm thick masts (most other foils on the market). It's even stiffer and any other carbon mast on the market today. This gives you more control and fast input from your feet to the front wing.
The 750mm mast is mostly used on bigger surf, downwinders and more advanced riding or as a surfy option for kite foiling.
Other mast sizes available:
450mm (15.7 inches),
600mm (23.6 inches),
680mm (26.6 inches),
750mm (29.5 inches),
1050mm (41.3 inches)
New kitesurf kit with the latest M92 and S370!
LIFT SPEED8/10
CONTROL7/10
AGILITY10/10
TOPSPEED8/10
New kitesurf kit with the latest M92 and S370!
This new setup, in combination with the w679 will give you a turning point in maneuvering, allowing you to reach even higher speeds while keeping stability.
The new M92 with increased chord and new profile will guarantee you maximum stiffness and even better performance than M91.
FUSION X-SERIES WINGS
HIGH PERFORMANCE
Sizes: X950 / X1300 / X1600 / X1950
The best part of the last 5 years has been the rise in hybrid development and crossover technology amongst sports. No where is this more evident than in foil boarding. The hydrofoil has become the common denominator in all of the surf and wind sports today.
Therefore, it reasons that its important to have a hydro wing-set capable of crossing between sporting genres with flawless performance and capability. Enter the X Series™ wings from Cabrinha. The design of the X Series™ recognizes and exploits the most important features needed in all hydrofoiling genres. Lift, efficiency and control are the three pillars that drive the X Series’ high performance and buttery smooth ride.
Through a combination of outlines and wing profiles the X series delivers a smooth lift and stable flight with precise turning and control.
The X Series’ efficiency is enhanced by our all new Cab Fusion mast and fuselage ecosystem. The Cab Fusion is a redesign from the bottom up to remove any unwanted ‘play’ in the system while streaming the connection between the wings and the fuselage. The resulting increase in stiffness and reduction in drag puts the X Series wings into an all new class of hydrofoils.
The X Series comes in 4 sizes to cover an incredibly wide range of rider weights and uses. If you do more than one sport you'll be confident that your entire foil system will crossover with an astounding level of performance across genres.
DESIGN PROFILESwept LE, Straight TE, Lean draft forward profile, moderate anhedral.
WING FEATURES
Loose and agile feel for superior maneuverability
Optimal efficiency and lift
Integrated fuselage with tapered fit
Incredible torsional stiffness and minimum drag
Full prepreg carbon construction
EPS core for superior strength to weight ratio
Moderate anhedral for a more efficient lift platform
Draft forward profile for a forgiving ride and early predictable lift
TECH SPECS
X950- 950cm^2, WS 630mm, AR 4.2, Vol 1.18L
X1300- 1300cm^2, WS 780mm, AR 4.7, Vol 1.6L
X1600- 1600cm^2 WS 900mm, AR 5.05, Vol 2L
X1950- 1950 cm^2, WS 1000mm, AR 5.13, Vol 2.5L
Set includes:
Front wing, wing covers.
The Broad Spectrum Carve (BSC) wings are a new direction into easy to ride wings, with good amount of performance embedded to the design. Perfect for all round riding including entry level riders.
The larger sizes are ideal for PUMPING, SUP, WINGING, WAKE. As we go down on sizing, 890-810-740 are high performance PRONE, WINGING and KITE wings.
For the BSC wings we use a refined foil section, with extensive speed range, and stability. This makes the BSC wings ideal for all levels of riders and conditions. The 890 / 810 / 740 sizes are designed for performance PRONE, WINGING and KITE foiling. These wings are stable, fast and turn on a dime.
The 1120 and 1060 are the easiest wings for all levels, heavier riders and all rounders for WING, SUP, WAKE and PUMP. Very early lift, butter smooth riding, good speed range, and great turning for their size. The 970 would be the all levels wing for all styles and levels of riding. The 890-810-740 are faster, more technical wings, designed for the skilled SUP, PRONE, WINGING riders who are looking for higher performance in a very easy to ride package.
As with every AXIS front wing, the graphics on the wings give you all possible measurements so you can best compare and also quickly swap pieces or get new accessories for your foil.
Compatible with the Red fuselages
AXIS BSC 970 Carbon Wing
Technical Data:
WINGSPAN: 970 mm / 38.2 inches
MAX CHORD: 190mm / 7.5 inches
ASPECT RATIO: 6.27
ACTUAL AREA 1572 square cm / 244 square inches
PROJECTED AREA: 1501 square cm / 233 square inches
VOLUME: 2313 cubic cm / 141 cubic inches
Recommended use:
WING Surfing for all levels and medium + conditions. Super stable for the size
Downwinding - Medium+ conditions and intermediate+ level
SUP / Surf - Medium+ conditions and intermediate level
Wake foiling - Intermediate+ level
Pump foiling - Intermediate+ level
Windsurf foiling - Intermediate+ level
Kite foiling - Light wind - All levels
Here is what the experts say:
The BSC wings are incredibly easy to ride. Bigger sizes ideal for lighter days and bigger dudes. Smaller sizes more surfy and faster. Medium AR makes them a bit slower but still faster than last years all rounds.
Rear Wing Options:
500mm Carbon for max control, stability and slower ride (entry levels)
460mm Carbon for high speed and loose turning (advanced)
420mm Carbon for the ultimate performance (speed and turning - intermediate +). One of our favorite rear wings for fast riding and carving.
440mm Carbon for control and stability (all levels)
400mm Carbon for looser feel and carvy turns while still maintaining good amount of control (Intermediate)
390mm Carbon for Wing and Surf with good turning control and additional glide
370mm Carbon for loose feel and fast turning, with less stability (intermediate). The rear wing that does it all
340mm Carbon for even looser feel and even less drag and more speed. (advanced)
500mm Anhedral Carbon specific to windsurf foiling
When you purchase an AXIS carbon front wing we include an AXIS padded cover with zipper, in heather gray, and AXIS branding, for safer setup, transportation and storage.
Improved by nature
KUJIRA II RANGE
•Unleash your full potential
Allow riders of all levels to progress further and push the limit.
•Pure glide experience
Precise design with minimal drag for an enhanced glide with effortless pumping and low stall speed. Keeps you in full control and allows to fly at low speeds.
•Carve with confidence
The tubercles on the edge of the front wing in combination with our new fuselage and selection of stabilizers allows for smooth rail to rail riding as well as tight turns and control at high speeds.
•Fast acceleration
Ease of generating speed with a moderate front foot pressure for maximum acceleration.
•Comfortable ride
The winglets reduces and redirects the angle of the vortex for less vibrations and more stability for a smooth and predictable ride.
SIZES:
KUJIRA II - 650 / 32
Ideal for the most demanding conditions. Provides confidence in big waves, strong winds, tow-in sessions by maintaining a comfortable and stable ride even when pushing to the limit.
Surface: 650 cm2
Wingspan: 690 mm
Chord: 114 mm
Aspect Ratio: 7,4
Back wing: 32 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
KUJIRA II - 800 / 34 to 1250 / 40
Ideal for the most demanding conditions. Provides confidence in big waves, strong winds, tow-in sessions by maintaining a comfortable and stable ride even when pushing to the limit.
800 / 34
Surface: 800 cm2
Wingspan: 784 mm
Chord: 126 mm
Aspect Ratio: 7,7
Back wing: 34 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
950 / 38
Surface: 950 cm2
Wingspan: 870 mm
Chord: 136,5 mm
Aspect Ratio: 8
Back wing: 36 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
1100 / 38
Surface: 1100 cm2
Wingspan: 938 mm
Chord: 147 mm
Aspect Ratio: 8
Back wing: 38 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
1250 / 40
Surface: 1250 cm2
Wingspan: 1018 mm
Chord: 155,5 mm
Aspect Ratio: 8,3
Back wing: 40 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
KUJIRA II - 1400 / 42
Not only it is ideal for heavier riders, it is designed for pure carving fun, playfulness in light wind and perfect for downwind with great stability.
Surface: 1400 cm2
Wingspan: 1096 mm
Chord: 162,5 mm
Aspect Ratio: 8,6
Back wing: 218 cm2
Mast: Carbon 75 cm / 85 cm or HD 80 cm
HD Fuselage: 65cm
*The Kujira II stabilizers are designed specifically to perform in combination with the front wings for the ideal balanced set up. Depending on the conditions, foiling disciplines, and riding style, changing the back wing can enhance your ride and bring an entirely different sensation and level of performance.
To extend the range of your set up :
Size down for: stronger conditions, more looseness, more speed, less back foot pressure.Size up for: lighter conditions, increase power, more stability, more pumping efficiency.
The IC6 850 is very accessible and offers a surprising potential for progression so it is really the ideal “first” foil purchase.- Very accessible- Versatile, very intuitive, and predictable- Large range of use- Compatible with all boardsArea: 850cm²Weight: 1.09kgMade in our specific technology called Injected Carbon, our wings and stabilizers are very tough and very durable. This technology makes our IC6 wings a lot more ding resistant than conventional carbon wings. The front wing has a metal insert where the connector extending out of the wing is fully machined via CNC for a very solid and perfect assembly.The fuselage and mast are made of aluminium. The fuselage plugs directly into the aluminium mast and at the top a 4-bolt plate that can be plugged in to get the foil compatible with any boards fitted with tracks. Alternatively, a selection of optional standards like KF, DeepKF or Tuttle heads is also available.This foil is not only versatile but it’s also very intuitive and predictable. The take-off is really progressive, the ride in the air super smooth. You have complete control on the speed and on your path.850cm3 is the size of the front wing and it was especially designed to have the largest possible range of use. It can fly at very low speed, its handling is impressive when carving and it’s got a very nice speed potential up or downwind.The IC6 850 V2 is designed for anyone looking for a first foil purchase or simply for a versatile setup able to deliver tons of fun on the water.
The MA1350 Front Wing is a mid-aspect ratio wing ideal for all rider weights. Easily generates lift without pumping. This performance wing is fast turning, with early planing ability for lighter wind conditions or heavier riders. Suitable for Kite, Wing, Surf and Tow Foiling.
Features
Higher speed top end performance
Extremely fast and responsive turning radius
Incredibly efficient
Insane glide and pumpability
Materials
Carbon Pre-preg
Freefoil | SurfKeep your precious foil looking new. The set includes a Tool Pouch and cover for the Front Wing, Stabilizer, Fuselage, 71 or 92cm Mast, and Mast Base. The 420 denier Nylon covers fit neatly in the optional Foil Bag that’s designed for traveling and busy airports. Five-millimeter closed-cell foam padding and additional edge polyester webbing protect all trailing edges. The handy tool pouch keeps all your hardware and tools in one place. Even the mast cover features a screw pocket. Now, you're covered.Delivery:Component covers and tool pouch.Measurements:
Front Wing Cover 1250: ca. 80 x 32 cm / ca. 32 x 12 inches
Stabilizer Cover 300: ca. 45 x 18 cm / ca. 18 x 7 inches
Fuselage Cover 70: ca. 77 x 10 cm / ca. 30 x 4 inches
Mast Cover 92: ca. 98 x 17 cm / ca. 38 x 7 inches
Mast Cover 71: ca. 78 x 17 cm / ca. 31 x 7 inches
Mastbase Cover: ca. 26 x 13 cm / ca. 10 x 5 inches
Tool Pouch S: ca. 25 x 13 x 8cm / ca. 10 x 5 x 3 inches
Features:
5MM PADDING: Thick padding for maximum protection.
420 DENIER NYLON: Tough. Durable.
FOIL BAG READY: Designed to fit into the optional Foil Bag.
The mast length of 75cm is ideal for SUP-, SURF, Wake and Wingfoiling. The Indiana mast profile ensures amazing flexional and torsional stiffness. The aluminum masts transmit the control impulses very quickly and directly from the board to the foil.
For one complete Foil you need to follow this 7 steps:Step 1: Choose one of four FrontwingsStep 2: Choose one of two StabilizersStep 3: Choose one of two FuselagesStep 4: Take the Set of Angle AdaptorsStep 5: Choose one of three Mast lengthsStep 6: If you have a board with two US finboxes/tracks you choose the Baseplate. If you have a Deep Tuttle/Tuttle Box you choose the Deep Tuttle/Tuttle Adaptor Head AND the Tuttle Adaptor PlateStep 7: Take the Set of Mast / Fuselage Screw
GRAVITY CARBON 2200
FLY IN FULL CONTROL
The foils of the Gravity line are designed to provide a solid lift with a smooth take-off and great carving potential.
Smooth take-off
Stability and lift
Area: 1760 cm²Span: 90 cmAspect Ratio: 4.6Weight: 1.95 kg (wing only)
The F-ONE Alu Fuselage 70 provides an ultra-rigid wing connection. Built in aluminum, it is very strong and allows the suitable front wings and stabilizers to be connected effortlessly.
• Super stiff wing connection• Solid aluminum construction• Slender and reinforced hydrodynamic section
This fuselage connects directly to F-ONE aluminum masts. It is made of superior-grade aluminum 6061, CNC machined with high precision and fully anodized. The aluminum profiles make the most of this homogeneous material to offer perfect rigidity, both in torsion and in bending.This fuselage is recommended for the IC6 650 V3 front wing. It is supplied with the necessary screws to connect the front wing (2x M6-25mm and 2x M6-15mm), the mast (2x M6-25mm) and the stabilizer (2x M6-15mm).You cannot use a carbon mast on this fuselage.
AERO 2500SIZES: 2500
Good things come to those who wait! Our next generation of Aero Surf Foils will blow your mind! The new wings are highly efficient, keep flying as long as you want and offer incredibly fluid and forgiving turning!Our new range of Aero Surf Foils comes with multiple size front and back wings as well as two fuselage options for different conditions and rider weights. Completely revamped Carbon front wings in 1500, 2000 and 2500cm can be combined with 365 and 295 cm Carbon back wings and two different length fuselages. Our newly designed 75cm Alu mast with special profile and wider chord length offers rigidity and response you’d only expect from carbon.Aero Foil 2500 (Big Boy SUP): 2500 carbon front wing / 365 back wing / 80cm fuselage. Ideal for riders above 90kg and up to head high surf as well as SUP Downwinders
€712.00*
This website uses cookies to ensure the best experience possible. More information...